Please wait while the page loads...

Ford Fusion Check Engine Light Flashing

Although there are countless ability causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are several normal causes incorporating something as simple as a loose gas cap. Diverse normal reasons for a Check Engine Light are dirty mass airflow sensor, a malfunction with the fuel injection system, faulty emissions control part, damaged oxygen sensor, faulty head gasket, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Ford Certified Technicians and the certified service protocol to isolate the root problem and repair it as basic to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Ford issue was fixed.

Every Ford Fusion was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the car on its central systems. The sensors are usually detecting conditions while sending data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what exactly is erroneous nor what to do about it. That’s where we come in; Bill Estes Ford Brownsburg provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Extraordinarily Qualified Service professional.

How much does it cost to get the engine light checked?

The average cost for a check engine light diagnosis & testing is customarily between $88 and $111. The excellent news, Bill Estes Ford Brownsburg offers complimentary multi-point inspections and free diagnostics, in most cases, to help select the cause of your check engine light. The check engine light warns of issues ranging from a gas cap that's not properly tightened to a more strict failure like a detrimental catalytic converter or a problem with one of the car's oxygen sensors, so it excellent to get the suitable code reading and diagnosis.

How many miles can you drive with the check engine light?

Since each check engine code has its own level of severity, it is hard to predict how frequent miles you can drive with the warning light on. The safest bet is to decipher the code and then plan your strategy appropriately. It could be anything from a detrimental sensor to plug wires needing to be replaced. If you check engine light is flashing, we advise that you pull over and contact Bill Estes Ford Brownsburg to help choose if your vehicle is safe to drive in or if we advise a tow truck.

What could cause the check engine light to come on in a Ford Fusion?

When your check engine light comes on, this could be as coherent as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a precarious problem that could cause precarious wear and tear to your engine and come with a generous repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow continuously means something less precarious but a shining check engine light illustrates that your vehicle’s engine is in precarious trouble and service is needed abruptly. If your check engine light is shining in your Ford Fusion, we tremendously recommend not to drive the vehicle and schedule Ford service now. Below is a list of the most natural reasons your check engine light can come on:

  • Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, common as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be less competent when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your Ford Fusion's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to read the polite mixture of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or contrasting item can wreak havoc on your Ford Fusion if it’s not installed perfectly. These aftermarket parts and accessories can drain the battery, trigger the check engine light, or even prevent the vehicle from starting. If these issues sound known, bring your Fusion to Ford and have our team of certified mechanics ensure that your aftermarket items were installed correctly and aren't causing any issue. Getting accessories, especially aftermarket parts and accessories, or using OEM parts first place might rate some bit more but could save you money from having to get poor work and damage caused by poor installation work corrected.
  • Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Ford Fusion is what determines how much fuel is crucial to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to responsive changes, like altitude. If your Ford Fusion is having trouble starting, idling rough or has a precipitous change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.
  • One of the most common and frequent cause is that your Ford Fusion gas cap is loose, damaged or missing. The gas cap for your Ford Fusion serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is long-established or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on shortly after you put gas in your Ford Fusion, first thing you should check is to make convinced the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • The battery is low or dead. The battery in your Ford Fusion is every vital. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did a lot decades ago, and they don't certainly require maintenance. The price of a new one depends on the type of Ford you drive, but check our prevailing service coupons and specials.
  • New Spark Plugs or Plug Wires are crucial for your Ford Fusion. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or long-established, you will experience poor performance and reduced power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, leading to more expensive repairs.
  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your Ford Fusion’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is usually caused by neglected maintenance, which is why Bill Estes Ford Brownsburg offers a complimentary multi-point inspection with every Ford service. If you have an issue with your catalytic converter and don't get it repaired, your Ford Fusion will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause contrasting problems from overheating.
  • Your Ford Fusion has a vacuum leak. Every Ford Fusion has a vacuum system that performs a expansive variety of functions. The vacuum system also helps cut harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, especially if they’re exposed to intense heat or extreme agile.

Ford Fusion Check Engine Light

A flashing light indicates that the problem is unhealthy and if not taken care of shortly may result in dominant damage to the car. If the check engine light in your Ford Fusion starts flashing, that means that the problem needs hasty attention and your Ford should be brought in shortly. This twinkling light ordinarily hints a perilous engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can immediately raise the temperature of the catalytic converter to a point where damage is achievable, requiring an pricey repair. Some owners ask if spark plugs cause the check engine light to flash? This can exclusively be the cause. A destructive, old or dirty spark plug can cause the engine to misfire. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a very expensive repair. If your check engine light is flashing, please contact our team of automotive experts at Bill Estes Ford Brownsburg urgently by calling 3177903264.

Ford Fusion Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that scant light on your vehicle’s dashboard suddenly illuminates, but in reality, it is not something that should cause you to shut down in fear correct away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your Fusion. There are hundreds of assorted codes that your check engine light can represent. While that sounds daunting, with a scant patience, tackling mandatory diagnostics will give you useful knowledge about your vehicle and will also allow that Check Engine Light to do what it is really supposed to do: be your guide. Unfortunately, discernible and satisfying vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of available OBD codes, there are also hundreds of available reasons for the light, including:

  • Computer output circuit issues
  • Transmission issues
  • Emissions controls issues
  • Bad Spark Plugs
  • Ignition system faults
  • Fuel and air metering systems problems
  • O2 Sensor
  • Old Battery
  • Loose Gas Cap or Missing Gas Cap

This is why it is important for someone who does not have a lot of automotive knowledge to not assume what a code means. If the engine light comes on due to a precarious concern, you risk bad your car further by not repairing the issue right away. When your check engine light comes on, you should get it checked out quickly by a certified Ford mechanic. Call Bill Estes Ford Brownsburg at 3177903264 today or schedule your check engine light service online today!

What Does the Check Engine Light Mean?

One of the most usually misunderstood lights or indicators in your Ford Fusion is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in a few different ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a assortment of things for your Ford Fusion. Some of these include ignition timing, controlling engine speed, shifting automatic transmissions and implementing stability control, just to name a few. With that being said, the check engine light can mean a variety of detectable things. It can be as straightforward as your gas cap being loose or as alarming as engine knocking. If your check engine light is on in your Ford Fusion, contact Bill Estes Ford Brownsburg. Contact Bill Estes Ford Brownsburg today! Our Ford service department can help you find out what code is turning your check engine light on or diagnose why your check engine light is flashing.

Is it safe to drive your Ford Fusion with the check engine light on?

If the check engine light is flashing, this means that there is a impressive issue and it is recommended to service your Ford Fusion shortly. This question is not excessively straightforward because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be able to drive. This is commonly indicated by a effective glow of the check engine light. If you notice a difference in the performance of the vehicle, it could be an indication of a more compelling problem. Call the experts at Bill Estes Ford Brownsburg by dialing 3177903264 so you can describe the issues. Or cut your speed and bring your Ford to our certified mechanics as soon as conceivable.

Check Engine Light Service Ford Fusion

What do you do when you’re driving along in your Ford Fusion and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Ford owners, your heart sinks a little because you have little idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t represent you have to pull the automobile over to the side of the road and call a tow truck, but it is recommended that you get your Ford Fusion checked as soon as functional. Ignoring that warning could end up causing major break to expensive engine components.

When your Ford Fusion's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t prudent, a computer turns on your check engine light. This amber or yellow light is frequently labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is read with an computerized scan tool that is used by our Ford auto repair mechanics at Bill Estes Ford Brownsburg. There are also a number of somewhat low-priced code readers that are designed for do-it-yourselfers, should you embrace that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an professional professional to represent the issue and repair it.

Will the check engine light reset itself?

The check engine light on your Ford Fusion will ordinarily shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going reasonable, and you did several of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your Ford Fusion light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Bill Estes Ford Brownsburg so the light and code can be double-checked and reset.