Please wait while the page loads...

Check Engine Light Service 2013 Ford Fusion

What do you do when you’re driving along in your Ford Fusion and rapidly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Ford owners, your heart sinks a little because you have little idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your 2013 Ford Fusion checked as soon as accessible. Ignoring that warning could end up causing hefty damage to expensive engine components.

When your 2013 Ford Fusion's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t impressive, a computer turns on your check engine light. This amber or yellow light is typically labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is learn with an electronic inspect tool that is used by our Ford auto repair mechanics at Bill Estes Ford Brownsburg. There are also a number of relatively bargain code readers that are designed for do-it-yourselfers, should you elect for that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced licensed to mean the issue and repair it.

Is it safe to drive your 2013 Ford Fusion with the check engine light on?

This question is not exceedingly classic because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be dependable to drive. This is typically indicated by a factual glow of the check engine light. If you notice a difference in the performance of the vehicle, it could be an indication of a more fair problem. If the check engine light is shining, this means that there is a fair issue and it is recommended to service your Ford Fusion shortly. Call the experts at Bill Estes Ford Brownsburg by dialing 3177903264 so you can describe the issues. Or reduce your speed and bring your 2013 Ford to our certified mechanics as soon as authentic.

What Does the Check Engine Light Mean?

One of the most typically misunderstood lights or indicators in your 2013 Ford Fusion is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in assorted contrasting ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a variety of things for your 2013 Ford Fusion. Some of these include ignition timing, shifting automatic transmissions controlling engine speed, and implementing stability control, just to name a few. With that being said, the check engine light can mean a variety of correct things. It can be as simple as your gas cap being loose or as relentless as engine knocking. If your check engine light is on in your 2013 Ford Fusion, contact Bill Estes Ford Brownsburg. Contact Bill Estes Ford Brownsburg today! Our Ford service department can help you find out what code is turning your check engine light on or diagnose why your check engine light is glaring.

2013 Ford Fusion Check Engine Light

If the check engine light in your 2013 Ford Fusion starts flashing, that means that the problem needs hasty attention and your Ford should be brought in suddenly. A flashing light indicates that the problem is harsh and if not taken care of suddenly may result in important damage to the vehicle. This blinking light usually indicates a impressive engine misfire allowing unburned fuel to be discharged into the exhaust system. There it can expeditiously hike the temperature of the catalytic converter to a point where damage is likely, requiring an expensive repair. Various owners ask if spark plugs cause the check engine light to flash? This can exactly be the cause. A bad, old or dirty spark plug can cause the engine to misfire. If your check engine light is glaring, please contact our team of automotive experts at Bill Estes Ford Brownsburg suddenly by calling 3177903264. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a excessively expensive repair.

Will the check engine light reset itself?

The check engine light on your 2013 Ford Fusion will commonly shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going correct, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2013 Ford Fusion light will go off after about 20-40 miles. If you drive over that fee and the light is still on, you will need to bring it in to Bill Estes Ford Brownsburg so the light and code can be double-checked and reset.

2013 Ford Fusion Check Engine Light Flashing

Although there are countless capability causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are assorted common causes including something as authentic as a loose gas cap. Alternative common reasons for a Check Engine Light are a malfunction with the fuel injection system, dirty mass airflow sensor, faulty head gasket, faulty emissions control part, damaged oxygen sensor, or defective spark plugs to name plentiful. No matter what is the root cause of the Check Engine Light, we have the Ford Certified Technicians and the certified service protocol to isolate the root problem and repair it as crucial to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Ford issue was fixed.

Every 2013 Ford Fusion was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the car on its practical systems. The sensors are continuously detecting conditions while sending data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what absolutely is erroneous nor what to do about it. That’s where we come in; Bill Estes Ford Brownsburg provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Hugely Qualified Service technological.

What could cause the check engine light to come on in a 2013 Ford Fusion?

When your check engine light comes on, this could be as prevalent as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a unhealthy problem that could cause unhealthy damage to your engine and come with a big repair bill. Depending on your make and model, the check engine light will illuminate or blink. A normal glow commonly means something less unhealthy but a flashing check engine light illustrates that your vehicle’s engine is in unhealthy trouble and service is needed immediately. If your check engine light is flashing in your 2013 Ford Fusion, we extraordinarily advocate not to drive the vehicle and schedule Ford service today. Below is a list of the most common reasons your check engine light can come on:

  • Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, known as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be fewer efficient when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your 2013 Ford Fusion's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to pick the honest mixture of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
  • Your 2013 Ford Fusion has a vacuum leak. Each Ford Fusion has a vacuum system that performs a wide vary of functions. The vacuum system also helps lower harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can parched out and crack, immensely if they’re exposed to exciting heat or extreme bitter.
  • The battery is low or dead. The battery in your 2013 Ford Fusion is each threatening. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did a few decades ago, and they don't actually require maintenance. The price of a new one depends on the type of Ford you drive, but check our existing service coupons and specials.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or other item can wreak havoc on your 2013 Ford Fusion if it’s not installed well. These aftermarket parts and accessories can drain the battery, trigger the check engine light, or even prevent the vehicle from starting. If these issues sound cognizant, deliver your Fusion to Ford and have our team of certified mechanics ensure that your aftermarket items were installed accurately and aren't causing any issue. Getting accessories, immensely aftermarket parts and accessories, or using OEM parts earliest place might cost a little bit more but could save you money from having to get low function and damage caused by low installation function corrected.
  • Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Ford Fusion is what determines how much fuel is needed to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to certain changes, like altitude. If your Ford Fusion is having trouble starting, idling rough or has a speedy change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.
  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your 2013 Ford Fusion’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is usually caused by neglected maintenance, which is why Bill Estes Ford Brownsburg offers a complimentary multi-point inspection with each Ford service. If you have an issue with your catalytic converter and don't get it repaired, your 2013 Ford Fusion will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause other problems from overheating.
  • One of the most commonplace and copious cause is that your 2013 Ford Fusion gas cap is loose, damaged or missing. The gas cap for your 2013 Ford Fusion serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is erstwhile or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't fancy. If your check engine light turns on now after you put gas in your 2013 Ford Fusion, earliest thing you should check is to make convinced the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • New Spark Plugs or Plug Wires are needed for your 2013 Ford Fusion. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or erstwhile, you will experience low performance and reduced power. In a bit extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, considerable to more fancy repairs.

How much does it cost to get the engine light checked?

The check engine light warns of issues ranging from a gas cap that's not well tightened to a more critical failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it good to get the suitable code reading and diagnosis. The average cost for a check engine light diagnosis & testing is frequently between $88 and $111. The good news, Bill Estes Ford Brownsburg offers complimentary multi-point inspections and free diagnostics, in most cases, to help opt for the cause of your check engine light.

How many miles can you drive with the check engine light?

Since each check engine code has its own level of severity, it is crucial to predict how many miles you can drive with the warning light on. If you check engine light is flashing, we recommend that you pull over and contact Bill Estes Ford Brownsburg to assist mean if your car is safe to drive in or if we recommend a tow truck. The safest bet is to decipher the code and then plan your strategy accordingly. It could be anything from a bad sensor to plug wires needing to be replaced.

2013 Ford Fusion Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that little light on your vehicle’s dashboard urgently illuminates, but in reality, it is not something that should cause you to shut down in fear honest away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your Fusion. There are hundreds of numerous codes that your check engine light can indicate. While that sounds daunting, with a few patience, tackling essential diagnostics will give you satisfactory knowledge about your vehicle and will also allow that Check Engine Light to do what it is actually supposed to do: be your guide. Unfortunately, helpful and helpful vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of feasible OBD codes, there are also hundreds of feasible reasons for the light, including:

  • Loose Gas Cap or Missing Gas Cap
  • Computer output circuit issues
  • Ignition system faults
  • Bad Spark Plugs
  • Fuel and air metering systems problems
  • Emissions controls issues
  • Transmission issues
  • O2 Sensor
  • Old Battery

This is why it is enormous for someone who does not have assorted of automotive knowledge to not assume what a code means. When your check engine light comes on, you should get it checked out swiftly by a certified Ford technician. Call Bill Estes Ford Brownsburg at 3177903264 today or schedule your check engine light service online today! If the engine light comes on due to a hazardous concern, you risk bad your car further by not repairing the issue proper away.